Ремонт и прошивка игровых приставок FreeBoot XBOX 360 в Донецке

Печать

CR3 Lite Jumper Settings

 

CR3 Lite - самый универсальный чип. Для любых ревизий Xbox360.

The CR3 Lite comes with an adhesive foam pad and the positioning in pictures below. We changed the security sticker as so many cheap knock offs were ripping off our design. It fits nicely to the 360 faceplate now if you wish

 

We also used a high quality 48Mhz crystal - once the cheap knock offs hit the market you can be sure they will use the cheap ones which will be very poor performance.

cr3 lite lk jumpers

Here are the default settings for the LK Solder Jumpers. As past experience by thousands of users has shown, you should try different settings for your setup until you achieve the best performance. It always helps others to post your own personal results.

Phat (Non-Jasper)

LK1 - Short (Disable Crystal)
LK2 - Open (Enable 10 Ohm on CPU_RST)
LK3 - Short (C15 Enable)
LK4 - All Open (Slim Settings)

Phat (Jasper)

LK1 - Short (Disable Crystal)
LK2 - Short (Disable 10 Ohm on CPU_RST)
LK3 - Short (C15 Enable)
LK4 - All Open (Slim Settings)

Tip
For Phat RGH2, LK3 should be OPEN.
Slim (Trinity)

LK1 - Short (Disable Crystal)
LK2 - Short (Disable 10 Ohm on CPU_RST)
LK3 - Open (C15 Disable)
LK4 - Short 1-2 (300pF on CPU_RST to GND)
or
LK4 - All Open

Slim (Corona)

LK1 - Open (Enable Crystal)
LK2 - Short (Disable 10 Ohm on CPU_RST)
LK3 - Open (C15 Disable)
LK4 - Short 1-2 (300pF on CPU_RST to GND)
or
LK4 - Short 2-3 (100pF on CPU_RST to GND)
or
LK4 - All Open

The following CPU RESET CLEANER settings were taken from many users experiences and we compiled all the best settings into one easy board. If you want to read through some source material for these settings we suggest you goto this thread so you can see lots of feedback.

CPU RESET CLEANER (S2 DIP SWITCH)
To disable set 1 and 5 On and the rest OFF
You can use a mixture of 234 and 678. 1 and 5 must be set to OFF when using a combo.

(1) Bypass
(2) 1K ohm
(3) 2K ohm
(4) 3.3K ohm
(5) Bypass
(6) 470 pf
(7) 560 pf
(8) 680 pf

PLL_BYPASS CLEANER (S4 DIP SWITCH)

100nF has always proven great for Jaspers. I personally have success with 680pF. Others have reported their own better results with all the other values.

(1) N/A
(2) 680 pf
(3) 150 nf
(4) 100 nf (Default - Same as CAP solder Jumper on Rev C)
(5) 68 nf
(6) 47 nf

The wire install and setup is the same as the CoolRunner Rev C.

DemoN can now directly connect using the ribbon cable that is included with the DemoN (Programming and Enable/Disable feature)

ROL can be wired directly to one of the front LED's without any diode as its included on the CR3 as per this thread

Опрос на сайте

Какую Android-оболочку вы используете на своём смартфоне?

Способы оплаты

webmoneynalichka-2beznalprivat24 Bonus PlusMasterCardVisa

Преимущества IQS

Профессиональный ремонт ноутбуков, цифровых фотоаппаратов, XBOX 360, Sony PlayStation 3, PS Vita, PS3, PSP, iPhone 3g, iPhone 4S, iPad, iPad 2, и другой техники. Квалифицированные специалисты выполнят восстановление данных, прошивку psp, прошивку iPhone и активацию iPhone, прошивку XBOX 360, а также обновление навигатора.

Гарантия на все выполненные работы.